DMAC Solvent Recovery Plant
Equipment Description
This DMAC recovery system uses five-stage vacuum dehydration and one-stage high vacuum rectification to separate DMAC from water, and combines with vacuum deacidification column to obtain DMAC products with excellent indexes. Combined with evaporation filtration and residual liquid evaporation system, the impurities mixed in DMAC waste liquid can form solid residue, improve the recovery rate and reduce pollution.
This device adopts the main process of five-stage + two-column high vacuum distillation, which is roughly divided into six parts, such as concentration, evaporation, slag removal, rectification, acid removal and waste gas absorption.
In this design, the process design, equipment selection, installation and construction are targeted to optimize and improve, in order to achieve the goal of making the device run more stable, the finished product quality is better, the operating cost is lower, the production environment is more environmentally friendly.
Technical Index
DMAC wastewater treatment capacity is 5~ 30t / h
Recovery rate ≥ 99 %
DMAC content ~2% to 20%
FA≤100 ppm
PVP content ≤1‰
Quality of DMAC
|
项目 Item |
纯度 Purity |
水分 Water content |
乙酸 Acetic acid |
二甲胺 DMA |
|
单位 Unit |
% |
ppm |
ppm |
ppm |
|
指标 Index |
≥99% |
≤200 |
≤30 | ≤30 |
Quality of column top water
| 项目 Item |
COD |
二甲胺 DMA |
DMAC |
温度 temperature |
| 单位 Unit |
mg／L |
mg／L |
ppm |
℃ |
| 指标Index |
≤800 |
≤150 |
≤150 |
≤50 |
Equipment Picture
Related products
-
DMA Treatment Plant
Main Features During the DMF rectifying and recovery process, due to the high temperature and Hydrolysis, parts of the DMF will be disintergrated to FA and DMA. The DMA will cause odor pollution, and bring serious impact for the operation environment and the enterprise. To follow the idea of Environment protection, the DMA waste should be incinerated, and discharged without pollution. We have developed the DMA wastewater purification process, can get about 40% indus...
-
Dry Solvent Recovery Plant
Main Features Dry process production line emissions except DMF also contains aromatic, ketones, lipids solvent, pure water absorption on such solvent efficiency is poor, or even no effect. The Company developed the new dry solvent recovery process, revolutionized by the introduction of ionic liquid as the absorbent, can be recycled in the tail gas of solvent composition, and has the great economic benefit and environmental protection benefit.
-
Toluene Recovery Plant
Equipment Description The toluene recovery plant in the light of the super fiber plant extract section, innovate the single effect evaporation for double-effect evaporation process, to reduce energy consumption by 40%, combined with falling film evaporation and the residue processing continuous operation, reducing the polyethylene in the residual toluene, improve the recovery rate of toluene. Toluene waste treatment capacity is 12~ 25t / h Toluene recovery rate ≥99% ...
-
Residue Dryer
Equipment Description The residue dryer pioneered the development and promotion can make the waste residue produced by DMF recovery device completely dry, and form slag formation. To improve the DMF recovery rate, reduce the pollution of the environment, reducing the labor intensity of workers, too. The dryer has been in a number of enterprises to obtain good results. Equipment Picture
-
DMF Solvent Recovery Plant
Process brief introduction After the DMF solvent from the production process is preheated, it enters the dehydrating column. The dehydrating column is provided with heat source by the steam on the top of the rectification column. The DMF in the column tank is concentrated and pumped into the evaporation tank by the discharge pump. After the waste solvent in the evaporation tank is heated by the feed heater, the vapor phase enters the rectification column for rectif...
-
DCS Control System
System Description DMF recovery process is a typical chemical distillation process, characterized by a large degree of correlation between process parameters and a high requirement for recovery indicators. From the current situation, the conventional instrument system is difficult to achieve real-time and effective monitoring of the process, so the control is often unstable and the composition exceeds the standard, which affects the production efficiency of enterpri...